Fujitsu STYLISTIC ST4000P User Manual download pdf (Page 33)

Using Your Stylistic ST4000P

CALIBRATING THE PEN

Calibration of the pen adjusts the cursor position on the

screen relative to the position of the pen tip. You calibrate

the pen to adjust the distance error between where the

pen actually touches the screen and where the system

“thinks” the pen is touching. If the event you wish to

invoke is not displayed under the pen tip when you use

the pen, you should calibrate the pen.

Pen calibration may be required due to the following

situations:

• The pen is being used for the first time.

• The previous user of the Stylistic ST4000P Series pen

tablet PC writes with the opposite hand or at a

different pen angle.

• The system has been in use for some time and the pen

has not been recalibrated.

• The original system image has been restored.

To Calibrate the Pen

1. Open the Control Panel from the Start|Settings

menu, and double-tap the Pen Configuration icon. In

the Setup Property page, tap on [Calibrate] to start

calibration.

2. Position the Stylistic ST4000P Series pen tablet PC as

you normally would during use. Be sure to hold the

pen at the angle that you regularly use. Touch the

screen only with the pen tip; inadvertently touching

the screen with your finger or hand during the

calibration process, may result in faulty calibration.

3. Perform the calibration steps according to the

instructions on the screen. The calibration utility

displays a cross-hair symbol in the corners of the

screen, one corner at a time. Hold the pen as you

normally would while using the system and, as

accurately as possible, tap the center of each crosshair

as it is displayed.

4. When the Verify New Pen Calibration Settings

window appears, choose one of the following steps.

• If you are satisfied that you tapped the cross-hairs

accurately, tap Ye s . The taps that you performed in

step 3 are then used to calibrate the screen.

• If you do not want to use the new calibration, tap

No.

• If you want to enter a new calibration, tap

Recalibrate. The calibration instructions reappear.

• If you don’t tap the screen within 20 seconds, the

default settings will be used.

If you have successfully performed the procedure above,

the pen is now recalibrated, and you can use the system as

you normally would.

Replacing the Pen

With use, the pen tip may become worn or may pick up

foreign particles that can scratch the screen. A damaged

or worn tip may not move freely, causing unpredictable

results when using the pen. If your pen exhibits these

problems, contact your reseller to purchase replacements.

USING HOVERING MODE

Selecting the Pen Hovering application button on the

Stylistic ST4000P Series pen tablet PC provides you with

better cursor control. When the hovering option is

enabled, the cursor can be positioned over an icon

without activating it. This is useful when you are

performing procedures that require accurate cursor posi-

tioning, such as when simulating mouse rollover,

selecting a small icon, or beginning a paint session.

• To enable hovering, press the Function button

and the Right-Click button at the same

time.

• To disable hovering, press the Function button

and the Right-Click button again.

For help on Normal/Special Hover mode settings in the

Pen Configuration applet, press [F1] to invoke help from

within the applet.

CHARGING THE BATTERY

The Stylistic ST4000P Series battery can be charged while

it is installed in the pen tablet PC. To do so:

1. Connect a DC power source, such as the AC adapter,

to the DC input connector on the pen tablet PC. The

DC Input icon appears in the Status display. If the

battery charge is below 90%, the battery begins

charging and the Charging icon appears in the Status

display. If the battery charge is 90% or higher when

you connect DC power, the battery will not charge,

preventing battery overcharging.

2. Look at the Battery Gauge icon in the Status display

to determine the percent of charge in the battery. See

“Status Display” in Chapter 1 of this manual for a

description of the Battery Gauge icon.

As long as DC power remains connected to the pen tablet

PC, the charging process continues until the battery

charge reaches 100%. Charge times shown in Table 2-2,

“Battery Charging Time" are for a fully discharged

battery charging both while the pen tablet PC is and is

not in use.

Alb_UG.book Page 23 Friday, November 1, 2002 4:22 PM

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 73 74

Comments to this Manuals

No comments

Fujitsu STYLISTIC ST4000P User Manual Page 33

Comments to this Manuals

Related products and manuals for Infrared bulbs Fujitsu STYLISTIC ST4000P