Fujitsu LifeBook S7210 User Manual download pdf (Page 69)

Troubleshooting

POWER ON SELF TEST MESSAGES

The following is an alphabetic list of error-and-status

messages that Phoenix BIOS and/or your operating

system can generate and an explanation of each message.

Error messages are marked with an *. If an error message

is displayed that is not in this list, write it down and

check your operating system documentation both on

screen and in the manual. If you can find no reference to

the message and its meaning is not clear, contact your

support representative for assistance.

nnnn Memory Cache Passed

Where nnnn is the amount of system cache in kilobytes

successfully tested by the Power On Self Test. (This can

only appear if you have an SRAM PC Card installed.)

Floppy Disk drive A error or Floppy Disk drive B

error

Drive A: or B: is present but fails the BIOS Power On Self

Test diskette tests. Check to see that the drive is defined

with the proper diskette type in the Setup Utility, (See

BIOS Setup Utility on page 58 for more information) and

that the diskette drive is installed correctly. If the disk

drive is properly defined and installed, avoid using it and

contact your support representative.

*Extended Memory Failed at address line: xx

Extended memory not working or not configured prop-

erly. If you have an installed memory upgrade module,

verify that the module is properly installed. If it is prop-

erly installed, you may want to check your Windows

Setup to be sure it is not using unavailable memory until

you can contact your support representative.

nnnn Extended RAM Passed

Where nnnn is the amount of memory in kilobytes

successfully tested.

*Failure Fixed Disk n (where x=1-4)

The fixed disk is not working or not configured properly.

This may mean that the hard drive type identified in

your setup utility does not agree with the type detected

by the Power On Self Test. Run the setup utility to check

for the hard drive type settings and correct them if

necessary. If the settings are OK and the message appears

when you restart the system, there may be a serious fault

which might cause you to lose data if you continue.

Contact your support representative.

*Incorrect Drive A type – run SETUP

Type of floppy drive A: not correctly identified in Setup.

This means that the floppy disk drive type identified in

your setup utility does not agree with the type detected

by the Power On Self Test. Run the setup utility to

correct the inconsistency.

*Incorrect Drive B type – run SETUP

Type of floppy drive B: not correctly identified in Setup.

This means that the floppy disk drive type identified in

your setup utility does not agree with the type detected

by the Power On Self Test. Run the setup utility to

correct the inconsistency.

*Invalid NVRAM Data

Problem with NVRAM access. In the unlikely case that

you see this message you may have some display prob-

lems. You can continue operating but should contact

your support representative for more information.

*Keyboard controller error

The keyboard controller test failed. You may have to

replace your keyboard or keyboard controller but may

be able to use an external keyboard until then. Contact

your support representative.

*Keyboard error

Keyboard not working. You may have to replace your

keyboard or keyboard controller but may be able to use

an external keyboard until then. Contact your support

representative.

*Stuck Key

BIOS discovered a stuck key and displays the scan code

for the stuck key. You may have to replace your keyboard

but may be able to use an external keyboard until then.

Contact your support representative.

*Monitor type does not match CMOS – Run SETUP

Monitor type not correctly identified in Setup. This

error probably means your BIOS is corrupted, run the

setup utility and set all settings to the default conditions.

If you still get this error, contact your support represen-

tative.

*Operating system not found

Operating system cannot be located on either drive A: or

drive C: Enter the setup utility and see if both the fixed

disk, and drive A: are properly identified and that the

boot sequence is set correctly. Unless you have changed

your installation greatly, the operating system should be

on drive C:. If the setup utility is correctly set, your hard

drive may be corrupted.

*Parity Check 1 nnnn

Parity error found in the system bus. BIOS attempts to

locate the address and display it on the screen. If it

cannot locate the address, it displays ????. This is a poten-

tially data destroying failure. Contact your support

representative.

*Parity Check 2 nnnn

Parity error found in the I/O bus. BIOS attempts to

locate the address and display it on the screen. If it

cannot locate the address, it displays ????. This is a poten-

tially data-destroying failure. Contact your support

representative.

Elf S7210.book Page 59 Thursday, September 13, 2007 10:28 AM

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 119 120

Comments to this Manuals

No comments

Fujitsu LifeBook S7210 User Manual Page 69

Comments to this Manuals

Related products and manuals for Laptops Fujitsu LifeBook S7210