Fujitsu LifeBook S7210 User Manual download pdf (Page 70)

LifeBook S7000 Notebook

*Press <F1> to resume, <F2> to SETUP

Displayed after any recoverable error message. Press the

[F1] key to continue the boot process or the [F2] key to

enter Setup and change any settings.

*Previous boot incomplete – Default configuration

used

Previous Power On Self Test did not complete success-

fully. The Power On Self Test will load default values and

offer to run Setup. If the previous failure was caused by

incorrect values and they are not corrected, the next

boot will likely fail also. If using the default settings does

not allow you to complete a successful boot sequence,

you should turn off the power and contact your support

representative.

*Real time clock error

Real-time clock fails BIOS test. May require board repair.

Contact your support representative.

*Shadow RAM Failed at offset: nnnn

Shadow RAM failed at offset nnnn of the 64k block at

which the error was detected. You are risking data

corruption if you continue. Contact your support repre-

sentative.

nnnn Shadow RAM Passed

Where nnnn is the amount of shadow RAM in kilobytes

successfully tested.

*System battery is dead – Replace and run SETUP

The BIOS CMOS RAM memory hold up battery is dead.

This is part of your BIOS and is a board mounted

battery which requires a support representative to

change. You can continue operating but you will have to

use setup utility default values or reconfigure your setup

utility every time you turn off your notebook.

System BIOS shadowed

System BIOS copied to shadow RAM.

*System CMOS checksum bad –

Default Configuration Used

BIOS CMOS RAM has been corrupted or modified

incorrectly, perhaps by an application program that

changes data stored in BIOS memory. Run Setup and

reconfigure the system.

*System RAM Failed at offset: nnnn

System memory failed at offset nnnn of in the 64k block

at which the error was detected. This means that there is

a fault in your built-in memory. If you continue to

operate, you risk corrupting your data. Contact your

support representative for repairs.

nnnn System Memory Passed

Where nnnn is the amount of system memory in kilo-

bytes successfully tested.

*System timer error

The timer test failed. The main clock that operates the

computer is faulty. Requires repair of system board.

Contact your support representative for repairs.

Video BIOS shadowed

Video BIOS successfully copied to shadow RAM

EMERGENCY MEDIA PLAYER

DRIVE TRAY RELEASE

If for some reason the eject button fails, you can open

the DVD/CD-ROM tray with a paper clip or similar tool

inserted into the eject hole in the far right side of the

front of the tray. Straighten one side of a paper clip

and push it gently into the hole. The tray will pop out

a short distance.

MODEM RESULT CODES

The operating system and application software that is

factory installed detects the modem characteristics and

provides the necessary command strings to operate the

modem. The internal modem operation is controlled by

generic AT commands from the operating system and

application software. The standard long form result

codes may, in some cases, be displayed on your screen to

keep you informed of the actions of your modem. The

operating system and application software may suppress

display of the result codes.

Examples of result codes are:

■

NO CARRIER

■

NO DIALTONE

■

CONNECT 53000 (Connection complete

at 53,000 bps.)

■

ERROR

■

FAX

■

RING (This means an incoming call.)

■

BUSY

■

NO ANSWER

When using the internal modem with applications

that are not factory installed refer to the

application documentation.

Elf S7210.book Page 60 Thursday, September 13, 2007 10:28 AM

1 2 ... 65 66 67 68 69 70 71 72 73 74 75 ... 119 120

Comments to this Manuals

No comments

Fujitsu LifeBook S7210 User Manual Page 70

Comments to this Manuals

Related products and manuals for Laptops Fujitsu LifeBook S7210