Fujitsu M3097DE User Manual Page 1

C150-E100-01ENM3097DE/DG Image ScannerOperator's Guide

viii

ixCOMPONENTSINSTALLATION ANDCONNECTIONSOPERATINGINSTRUCTIONDOCUMENTSPECIFICATIONixCOMPONENTSINSTALLATION AND CONNECTIONSOPERATING INSTRUCTIONDOCUMENT

COMPONENTSAfter unpacking the scanner,confirm that all the components havebeen received. This chapter describes the components of thescanner, part na

1-11Cheking the ComponentsThese high precision components must be handled with care.Confirm that all the components shown in the following figure hav

1-2oADF lever!2Third party slotiADF paper chuteyPower switch!0Power inlet!1Interface connectors!3Memory covereDocumentholding padwDocument bedqDocume

1-3No. Functionq Document cover: Closed over and holds a document to be read.w Document bed: A document to be read is placed on the bed also calledFl

1-4 AssembliesThumb screwGuide A ASYPick roller 2BearingBearingPick roller 1StackerPad ASY

1-5 ArrangementThe operator panel is located at the upper right hand side of the scanner. The panel consists of anLCD (24 character x 2 line), LEDs

1-6 Button/LED FunctionName of the button Functionand LEDButton Next LCD displays the next screen.Previous LCD displays the Previous screen.← Moves t

1-7 Counter DisplayThe scanner is provided with the counter display.Paper counterAbrasion counterCounter FunctionPaper counter Paper counter counts t

M3097DE/DGImage ScannerOperator's Guide

1-8Operation statusOperation status is indicated by the following message:<Power-on><Reading><Waiting for Start> Scanner displays f

1-9Temporary error<Hopper empty>This message is displayed if there is no more paper on the ADF paperchute during a read operation in ADF mode.

1-10AlarmOne of the following message is displayed if an error occurs in the scanner. If one of the followingerror message is displayed, turn the pow

CHAPTER2The chapter describes how to install and connect the scanner.PrecautionsInspectionRemoving the Carrier Fixing BracketCable ConnectionMounting

2-1This section describes precautions when installing the scanner.Do not install the scanner in the following places and environments.• Place the sca

2-2InspectionThis section describes how to check the labels.Label BLabel ALabel A (An example)This device complies with Part 15 of the FCC Rules. Ope

2-3Label B (An example)012345678901234567890123456789ANSMODEL NAMERev.LabelIMAGE SCANNERM3097DECAO **** - *********MODELPART NO.SER. NO.DATE1997-**

2-4Removing the Carrier Fixing BracketTo keep the scanner from being damaged during shipping, the carrier unit is fixed with a bracket. Afterplacing

2-5Connect the power cable to the power inlet of the device and a power outlet.Press “O” side of the power switch to turn the power off.Power OFFPowe

2-6 Connecting the interface cable(M3097DE)Connect the video interface and RS-232C interface cables and secure them with hooks and screws.Connect the

iDecember, 1997 First editionRevised contentsSpecification No. C150-E101-01EN Date publishedEditionThis equipment has been te

2-7Mounting the StackerMount the stacker using the following procedure.q Mount the stacker.Hook the pins on the stacker to the claws on the image sca

2-8SCSI-ID setting (M3097DG)The default of SCSI-ID is 5. SCSI-ID is set by Setup mode of the operator panel. The procedure to set SCSIID is;1 Turn th

CHAPTER3OPERATING INSTRUCTIONThis chapter describes how to turn the power on, and also de-scribes button specification and reading mode setting.Refer

3-13This section describes how to turn the power on.Press “I” side of the power switch. The power goes on and the green Power lamp at the operatorpa

3-2Reading Mode Setting (M3097DE)This section describes the button specifications and setup details for each of the simplex (front-side),duplex (fron

3-3<Screen 4><Screen 5><Screen 6>7 Select Size by pressing or . Thenpress . The scanner displaysScreen 5.8 Select Resolution by

3-4<Screen 7><Screen 8><Screen 9><Screen 10>10 Select Back Density (when “Duplex” wasSelected) by pressing or . As thecurs

3-5Parameter DescriptionL.(Line) White level following is ON. Top 3mm part of the document must be left blank(grounding color is dropout color). It i

3-6Manual Feed Mode SettingIn this mode, the scanner waits for some predetermined time without issuing “Paper Empty” after alldocuments are read. Thi

CHAPTER4ADF DOCUMENT SPECIFICATIONThis chapter describes the document size and document gualityof the ADF.Document SizeDocument Quality

iiFUJITSU FRANCE S.A.Bâtiment Aristote,17 rue Olof palme94006 Créteil cedex,FRANCETEL:33-14-513-1616FAX:33-14-399-0700FUJITSU HONG KONG LimitedRoom 25

4-1Document SizeThe following figure shows document sizes that the scanner can read.(Unit : mm)ABMinimumMaximumBA148 (5.8 in)148 (5.8 in)105 (4.1 in)

4-2Document QualityThis section describes document types and weights available for the scanner, and precautions. Document typeThe recommended paper t

4-3When scanning a translucent document, set the density to light mode.Carbon-less papers have the chemical composition which damages the pad and pic

4-4

CHAPTER5SPECIFICATIONSThis chapter describes the installation specifications, dimen-sions, consumables, option.Installation SpecificationsDimensionsCo

5-1The following table lists the installation specifications of the scanner.Installation SpecificationsItem SpecificationWidth Depth HeightDimensions

5-2497234335285 696Dimensions(unit: mm)

5-3ConsumablesThe following table lists consumables used for the scanner. Be sure to keep some consumables in stock.Customer is responsible to chang

5-4OptionThe following table lists options of the scanner.Name Specification RemarkExtended Memory TBD 16MB, EDO SIMM, 72pin, 60nswithout parityOne p

CHAPTER6SETUP MODEThis chapter describes the setup mode of the scanner.Activating the Setup ModeContents of the Setup Mode

iiiIMPORTANT NOTE TO USERSREAD CAREFULLY ALL OF THIS MANUAL BEFORE USING THIS PRODUCT.IF NOT USED CORRECTLY, UNEXPECTED DAMAGES MAY BE CAUSED TOTHE US

6-1 Activating the Setup ModeThis section describes how to activate the setup mode.1 Turn the power ON. Then the scannerdisplays “Scanner Ready” on L

6-2Contents of the Setup ModeThis section describes the contents of the setup mode.No Item Description Selectable Defaultparameters1 Double feed chec

6-3 Setting double feed detectionWhen you set the using of double feed detection, you must set as follows:1 Press or and let thescanner display S

6-4 Setting IPC pre-set modeWhen you set the using of IPC-2 pre-set mode, you must set as follows:1 Press or and let thescanner display Screen 42

6-5• When IPC pre-set is executed in setup modeScanner checks that IPC-2D or IPC-3D are installed when the scanner enters in IPC pre-set.If IPC-2D or

6-6 Reset of abrasion counterWhen you reset the abrasion counter, you must set as follows:1 Press or and let thescanner display Screen 43.2 At Sc

6-7<Screen 45> Setting time-out limit1 Press or and let thescanner display Screen 45.2 At Screen 45, press to increase thenumber or press

6-83 At Screen A, if you want to let the offsetreturn to default, select “Yes” otherwise“No” then press . The scannerdisplays Screen B.4 At Screen B

6-9 Reviewing the IPC/Memory Status1 Press or and let thescanner display Screen 49.2 Screen 49 displays the IPC optioninstalled and total image m

6-10

ivPrefaceThis manual explains how to use the M3097DE/DG image scanner.This manual contains COMPONENTS, INSTALLATION AND CONNEC-TION, OPERATING INSTRUC

GL-1GLOSSARY OF TERMSA4 sizeA standard paper size used in Japan and other countries. Paper size is 210 x 297 mm (8.25 x 11.6 inches).Abrasion counte

GL-2Double feed detectionA function which detects the status when multiple sheets are fed in the ADF unit.dpiDots per inch.Drop-out colorA color whic

GL-3HexadecimalA base-16 numbering system(also commonly referred to as hex numbers). Since a base-16 systemrequires 16 digits, numbers 0 through 9 a

GL-4Letter sizeA standard paper size used in the U.S.A. and other countries. Paper size is 8-1/2 x 11 inches (215.9 x279.4 mm).Linedrawing modeSelec

GL-5Photograph mode (White level follower OFF)Selecting photograph mode makes brightness and contrast settings effective but prevents the thresholdfr

GL-6SETUP modeIn this mode, users can view or set a variety of function in Off-line.Simplex reading modeOnly the front side of the document is read i

IN-1INDEXA3 3-3A4 3-3Abrasion counter 1-7Activating the Setup Mode 7-1ADF 1-2, 1-3ADFLever 1-2, 1-3mode 1-6paper chute 1-2Ala

IN-2LabelA 2-2B 3-3Landscape 3-2LCD 1-5LCD Display 1-6LED 1-6LG (Legal) 3-3LT (Letter) 3-3Manualfeed mode 3-6start mode

IN-3the Power On 3-1the power switch off 2-5Units 1-2Units and Assemblies 1-2Weight 5-1 button 1-6 button 1-6(START) button 1

IN-4

vSpecial information, such as warnings, cautions are indicated as follows:WARNINGWARNING indicates that personal injury may result if you do not follo

vi

viiCONTENTSvii❑ CHAPTER 1 COMPONENTSChecking the Components ..............1-1Units and Assemblies ...