Fujitsu MCM3064AP User Manual Page 84
- Page / 202
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Host Interface
4-14 C156-E227-01EN
4.4.2 Defect sector management
Sector mapping is executed based on the ISO/IEC 10090 standard for 128 MB
media, the ISO/IEC 13963 standard for 230 MB media, the ISO/IEC 15041
standard for 540 and 640 MB media, and GIGAMO 1.3 GB 90 mm Magneto-
optical Disk System-System Description for 1.3 GB media. Basically, possibly
defective sector management is not required for the host.
Defective sectors cannot be deleted from the host, except for certifying recordable
areas. Recordable areas can be certified with the FORMAT UNIT command.
4.4.3 Automatic alternate sector assignment function
The ODD automatically assigns an alternate sector if a verify error is detected in
the ID or data section during the WRITE (I0) command, WRITE (12) command,
or WRITE AND VERIFY and ERASE command. Alternate sector information is
registered in SDL (Secondary Defect List) on media.
After automatic alternate assignment terminates successfully, the ODD does not
report any error.
For the criteria for executing alternate sector assignment processing, see Table
4.14, "Alternate sector assignment criteria."
Table 4.14 Alternate sector assignment criteria
Processing Alternate sector assignment
processing
Remarks
ID read error 128/230 MB media: 3 read errors in
3 sectors
540/640 MB or 1.3 GB media: 2
read errors in 2 sectors
-
Data error 5 or more bytes per interleave Verify Check is not performed unless it
is valid.
This criterion is inapplicable to the
ERASE command.
- MCM3064AP, MCM3130AP 1
- OPTICAL DISK DRIVES 1
- PRODUCT MANUAL 1
- FOR SAFE OPERATION 2
- Revision History 3
- Overview of Manual 5
- Attention 7
- Important Alert Items 10
- C156-E227-01EN vii 11
- REFERENCED STANDARDS 12
- Contents 13
- Illustrations 18
- CHAPTER 1 General Description 23
- 1.1.2 Reliability 25
- 1.1.4 Adaptability 25
- 1.1.5 Interface 26
- 1.2.1 Appearance 28
- 1.2.2 Configuration 29
- 1.2.3 Mechanical section 29
- 1.2.4 Control circuit section 30
- CHAPTER 2 Specifications 33
- 2.1.4 Error rate 37
- 2.1.5 Reliability 38
- 2.2.2 Appearance 40
- 2.2.3 Specifications of disk 42
- 2.3 Defect Management 43
- Tip of thermocouple 46
- Opening of disk outer wall 46
- 3.2 Mounting Requirements 47
- Installation Requirements 48
- 3-4 C156-E227-01EN 48
- C156-E227-01EN 3-5 49
- 3-6 C156-E227-01EN 50
- C156-E227-01EN 3-7 51
- 3-8 C156-E227-01EN 52
- 3.2.2 Installation direction 53
- 3.2.3 Center of gravity 54
- 3.2.4 Precautions on mounting 55
- 3.3 Power Supply Requirements 57
- 3.4 Cable Connections 58
- 3.5 Jumper Settings 60
- 3.5.2 Mode settings 61
- C156-E227-01EN 3-21 65
- 3-22 C156-E227-01EN 66
- 3.7 Mounting of Drive 67
- 3.8 Cable Connections 68
- 3.9.2 Connection check 69
- 3.10 Demounting of Drive 70
- CHAPTER 4 Host Interface 71
- 4.1 Pin Assignment 72
- 4.2 Signal Description 74
- 4.3 Interface Registers 76
- 4.4 Various Processes 83
- 4.4.5 Cache function 86
- Media is 91
- 4.4.8 LED Indications 92
- 4.5 ATA Commands 93
- 4.5.2 PACKET (A0h) 100
- 4.5.3 DEVICE RESET (08h) 101
- 4.5.4 CHECK POWER MODE (E5h) 102
- 4.5.6 GET MEDIA STATUS (DAh) 104
- 4.5.9 SERVICE (A2h) 106
- 4.5.8 NOP (00h) 106
- 4.5.10 SET FEATURES (EFh) 107
- 4.5.11 SLEEP (99h/E6h) 111
- 4.6 Packet Commands 113
- 4.6.1 Logical Unit Number 114
- 4.6.2 ERASE command 114
- 4.6.3 FORMAT UNIT command 115
- 4.6.4 INQUIRY command 116
- 4.6.5 MODE SELECT command 118
- Reserved Reserved 121
- Reserved 121
- 4.6.6 MODE SENSE (10) command 130
- 4.6.7 MODE SENSE (6) command 133
- 4.6.9 READ (10) command 135
- 4.6.10 READ (12) command 135
- 4.6.11 READ CAPACITY command 136
- 4.6.14 READ LONG command 140
- 4.6.16 REQUEST SENSE command 141
- 4.6.18 SEEK command 146
- IMMED Reserved 148
- 4.6.22 VERIFY command 149
- 4.6.23 WRITE (10) command 149
- 4.6.24 Write (12) command 150
- ByteChk Reserved 151
- 4.6.26 WRITE BUFFER command 152
- 4.6.27 WRITE LONG command 154
- 4.7 Timing 155
- 4.7 Timing 159
- C156-E227-01EN 4-89 159
- Host Interface 160
- 4-90 C156-E227-01EN 160
- C156-E227-01EN 4-91 161
- 4-92 C156-E227-01EN 162
- C156-E227-01EN 4-93 163
- 4-94 C156-E227-01EN 164
- C156-E227-01EN 4-95 165
- 5.1.2 Precautions 170
- Press the eject switch 173
- 5.3.1 Appearance 174
- 5.3.2 Write protect tab 176
- 5.3.3 Precautions 177
- 6.1 Diagnostics 183
- 6.2 Maintenance Information 184
- 6.2.2 Revision number 185
- Glossary 187
- C156-E227-01EN GL-3 189
- Acronyms and Abbreviations 191
- MCL3064UA 2-3 196
- MCM3064UB, MCM3130UB 2-2 196
- READER’S COMMENT FORM 199
Related products and manuals for Hardware Fujitsu MCM3064AP
Hardware Fujitsu FMW43SA1 User Manual
(4 pages)
(4 pages)
Hardware Fujitsu MHW2120BS User Manual
(296 pages)
(296 pages)
Hardware Fujitsu MHS2040AT User Manual
(40 pages)
(40 pages)
Hardware Fujitsu MB90890 User Manual
(7 pages)
(7 pages)
Hardware Fujitsu MHW2060AC User Manual
(278 pages)
(278 pages)
Hardware Fujitsu ADA-16FX User Manual
(17 pages)
(17 pages)
Hardware Fujitsu D1961 User Manual
(45 pages)
(45 pages)
Hardware Fujitsu MHT2060AT User Manual
(256 pages)
(256 pages)
Hardware Fujitsu MHZ2250BJ User Manual
(320 pages)
(320 pages)
Hardware Fujitsu MHV2120AT User Manual
(280 pages)
(280 pages)
Hardware Fujitsu SFP MSA User Manual
(1 pages)
(1 pages)
Hardware Fujitsu MHT2060BH User Manual
(264 pages)
(264 pages)
Hardware Fujitsu MB91460 SERIES FR60 User Manual
(103 pages)
(103 pages)
Hardware Fujitsu fi-5000N User Manual
(29 pages)
(29 pages)
© 2020, manymanuals.com. All rights reserved. | 1.966 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals