Fujitsu MCM3064AP User Manual Page 9
- Page / 202
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
C156-E227-01EN v
Important Alert Items
Important Alert Messages
The important alert messages in this manual are as follows:
A hazardous situation could result in minor or moderate personal injury if the
user does not perform the procedure correctly. Also, damage to the product
or other property, may occur if the user does not perform the procedure
correctly.
Task Alert message Page
Assembly and Installation
Device damage:
1) Do not expose to the drive any shock or vibration exceeding the
specification because it will fatally damage the drive. Be
particularly careful of this point when unpacking the drive.
2) Do not leave the drive in a dirty or contaminated environment.
3) Since the drive contains CMOS components that may be
destroyed by static discharge, keep the following points in mind
after unpacking:
•
Use an antistatic mat and wear a wrist strap when handling
the drive.
•
Hold the mounting frame when handling the drive. Do not
touch the printed wiring board unit except when required to
make the settings.
4) When handling the drive, hold both sides of the mounting
frame. When touching any part of the drive other than both
sides of the mounting frame, avoid applying force on the
location.
5) When handling the drive or making settings, do not press hard
on the tip of the header pin of the printed circuit board unit.
3-16
- MCM3064AP, MCM3130AP 1
- OPTICAL DISK DRIVES 1
- PRODUCT MANUAL 1
- FOR SAFE OPERATION 2
- Revision History 3
- Overview of Manual 5
- Attention 7
- Important Alert Items 10
- C156-E227-01EN vii 11
- REFERENCED STANDARDS 12
- Contents 13
- Illustrations 18
- CHAPTER 1 General Description 23
- 1.1.2 Reliability 25
- 1.1.4 Adaptability 25
- 1.1.5 Interface 26
- 1.2.1 Appearance 28
- 1.2.2 Configuration 29
- 1.2.3 Mechanical section 29
- 1.2.4 Control circuit section 30
- CHAPTER 2 Specifications 33
- 2.1.4 Error rate 37
- 2.1.5 Reliability 38
- 2.2.2 Appearance 40
- 2.2.3 Specifications of disk 42
- 2.3 Defect Management 43
- Tip of thermocouple 46
- Opening of disk outer wall 46
- 3.2 Mounting Requirements 47
- Installation Requirements 48
- 3-4 C156-E227-01EN 48
- C156-E227-01EN 3-5 49
- 3-6 C156-E227-01EN 50
- C156-E227-01EN 3-7 51
- 3-8 C156-E227-01EN 52
- 3.2.2 Installation direction 53
- 3.2.3 Center of gravity 54
- 3.2.4 Precautions on mounting 55
- 3.3 Power Supply Requirements 57
- 3.4 Cable Connections 58
- 3.5 Jumper Settings 60
- 3.5.2 Mode settings 61
- C156-E227-01EN 3-21 65
- 3-22 C156-E227-01EN 66
- 3.7 Mounting of Drive 67
- 3.8 Cable Connections 68
- 3.9.2 Connection check 69
- 3.10 Demounting of Drive 70
- CHAPTER 4 Host Interface 71
- 4.1 Pin Assignment 72
- 4.2 Signal Description 74
- 4.3 Interface Registers 76
- 4.4 Various Processes 83
- 4.4.5 Cache function 86
- Media is 91
- 4.4.8 LED Indications 92
- 4.5 ATA Commands 93
- 4.5.2 PACKET (A0h) 100
- 4.5.3 DEVICE RESET (08h) 101
- 4.5.4 CHECK POWER MODE (E5h) 102
- 4.5.6 GET MEDIA STATUS (DAh) 104
- 4.5.9 SERVICE (A2h) 106
- 4.5.8 NOP (00h) 106
- 4.5.10 SET FEATURES (EFh) 107
- 4.5.11 SLEEP (99h/E6h) 111
- 4.6 Packet Commands 113
- 4.6.1 Logical Unit Number 114
- 4.6.2 ERASE command 114
- 4.6.3 FORMAT UNIT command 115
- 4.6.4 INQUIRY command 116
- 4.6.5 MODE SELECT command 118
- Reserved Reserved 121
- Reserved 121
- 4.6.6 MODE SENSE (10) command 130
- 4.6.7 MODE SENSE (6) command 133
- 4.6.9 READ (10) command 135
- 4.6.10 READ (12) command 135
- 4.6.11 READ CAPACITY command 136
- 4.6.14 READ LONG command 140
- 4.6.16 REQUEST SENSE command 141
- 4.6.18 SEEK command 146
- IMMED Reserved 148
- 4.6.22 VERIFY command 149
- 4.6.23 WRITE (10) command 149
- 4.6.24 Write (12) command 150
- ByteChk Reserved 151
- 4.6.26 WRITE BUFFER command 152
- 4.6.27 WRITE LONG command 154
- 4.7 Timing 155
- 4.7 Timing 159
- C156-E227-01EN 4-89 159
- Host Interface 160
- 4-90 C156-E227-01EN 160
- C156-E227-01EN 4-91 161
- 4-92 C156-E227-01EN 162
- C156-E227-01EN 4-93 163
- 4-94 C156-E227-01EN 164
- C156-E227-01EN 4-95 165
- 5.1.2 Precautions 170
- Press the eject switch 173
- 5.3.1 Appearance 174
- 5.3.2 Write protect tab 176
- 5.3.3 Precautions 177
- 6.1 Diagnostics 183
- 6.2 Maintenance Information 184
- 6.2.2 Revision number 185
- Glossary 187
- C156-E227-01EN GL-3 189
- Acronyms and Abbreviations 191
- MCL3064UA 2-3 196
- MCM3064UB, MCM3130UB 2-2 196
- READER’S COMMENT FORM 199
Related products and manuals for Hardware Fujitsu MCM3064AP
Hardware Fujitsu FMW43SA1 User Manual
(4 pages)
(4 pages)
Hardware Fujitsu MHW2120BS User Manual
(296 pages)
(296 pages)
Hardware Fujitsu MHS2040AT User Manual
(40 pages)
(40 pages)
Hardware Fujitsu MB90890 User Manual
(7 pages)
(7 pages)
Hardware Fujitsu MHW2060AC User Manual
(278 pages)
(278 pages)
Hardware Fujitsu ADA-16FX User Manual
(17 pages)
(17 pages)
Hardware Fujitsu D1961 User Manual
(45 pages)
(45 pages)
Hardware Fujitsu MHT2060AT User Manual
(256 pages)
(256 pages)
Hardware Fujitsu MHZ2250BJ User Manual
(320 pages)
(320 pages)
Hardware Fujitsu MHV2120AT User Manual
(280 pages)
(280 pages)
Hardware Fujitsu SFP MSA User Manual
(1 pages)
(1 pages)
Hardware Fujitsu MHT2060BH User Manual
(264 pages)
(264 pages)
Hardware Fujitsu MB91460 SERIES FR60 User Manual
(103 pages)
(103 pages)
Hardware Fujitsu fi-5000N User Manual
(29 pages)
(29 pages)
© 2020, manymanuals.com. All rights reserved. | 1.320 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals