Fujitsu MHW2040AC User Manual Page 113
- Page / 278
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5.3 Host Commands
(13) IDLE (X’97’ or X’E3’)
Upon receipt of this command, the device sets the BSY bit of the Status register,
and enters the idle mode. Then, the device clears the BSY bit, and generates an
interrupt. The device generates interrupt even if the device has not fully entered
the idle mode. If the spindle of the device is already rotating, the spin-up sequence
shall not be implemented.
By using this command, the APS (Automatic Power Standby) timer function is
enabled and the timer immediately starts the countdown. When the timer reaches
the specified value, the device enters standby mode. The APS timer is set to
prohibition if the Sector Count register's value was "00h" when device has
received this command.
The APS timer allows the device to change to the standby mode automatically
after specified period. When the device enters the state which is waiting Host
Command, the timer starts countdown. If any command is not issued while the
timer is counting down, the device automatically enters the standby mode. If any
command is issued while the timer is counting down, the timer is initialized and
the command is executed. The timer restarts countdown after completion of the
command execution.
The period of timer count is set depending on the value of the Sector Count
register as shown below.
Sector Count register value Point of timer
0 [X’00’] Timeout disabled
1 to 240 [X’01’ to X’F0’]
(Value × 5) seconds
241 to 251 [X’F1’ to X’FB’]
((Value-240) × 30) min
252 [X’FC’] 21 minutes
253 [X’FD’] 8 hrs
254 to 255 [X’FE’ to X’FF’] 21 minutes 15 seconds
At command issuance (I/O registers setting contents)
1F7
H
(CM) X’97’ or X’E3’
1F6
H
(DH) x x x DV xx
1F5
H
(CH)
1F4
H
(CL)
1F3
H
(SN)
1F2
H
(SC)
1F1
H
(FR)
xx
xx
xx
Period of timer
xx
C141-E258 5-37
- MHW2060AC, MHW2040AC 1
- DISK DRIVES 1
- PRODUCT MANUAL 1
- FOR SAFE OPERATION 2
- Revision History 3
- Preface 5
- Operating Environment 6
- Conventions 6
- Attention 7
- Liability Exception 7
- Important Alert Items 9
- Manual Organization 11
- Contents 13
- Illustrations 19
- CHAPTER 1 Device Overview 23
- 1.1 Features 24
- 1.1.3 Interface 25
- 1.2 Device Specifications 26
- 1.3 Power Requirements 29
- 1.5 Acoustic Noise 33
- 1.6 Shock and Vibration 33
- 1.7 Reliability 34
- 1.8 Error Rate 35
- 1.9 Media Defects 35
- 1.10 Load/Unload Function 35
- 2.1 Device Configuration 40
- 2.2 System Configuration 41
- 2.2.3 2 drives connection 42
- 3.1 Dimensions 44
- 3.2 Mounting 45
- Connector 50
- 3.3.3 Device connection 51
- 3.4 Jumper Settings 52
- 3.4.4 CSEL setting 54
- 4.1 Outline 58
- 4.2 Subassemblies 58
- 4.3 Circuit Configuration 59
- C141-E258 4-5 61
- 4.4 Power-on Sequence 62
- 4.5 Self-calibration 63
- 4.6 Read/write Circuit 65
- 4.6.3 Read circuit 66
- 4.6.4 Digital PLL circuit 67
- 4.7 Servo Control 68
- Theory of Device Operation 72
- 4-16 C141-E258 72
- 4.7.3 Servo frame format 73
- 4.7.5 Spindle motor control 75
- CHAPTER 5 Interface 77
- 5.1 Physical Interface 78
- 5.2 Logical Interface 82
- 5.2.1 I/O registers 83
- 5.3 Host Commands 90
- 5.3.2 Command descriptions 94
- • Default function 110
- • Unload Feature: 110
- • Attribute ID 123
- • Raw attribute value 124
- • Status Flag 124
- • Current attribute value 124
- • Error logging capability 127
- • Check sum 127
- • SMART error logging 128
- • Command data structure 130
- • Error data structure 130
- • Status 130
- • SMART self-test 131
- • Self-test number 131
- • Self-test index 131
- • Test span 132
- • Current LBA under test 132
- • Current span under test 132
- • Feature Flags 133
- (CM) 1 1 1 0 0 1 0 0 149
- • SET MAX ADDRESS 180
- Password information 182
- • SET MAX SET PASSWORD 184
- • SET MAX LOCK 184
- • SET MAX UNLOCK 184
- • Description 186
- 5.3.3 Error posting 203
- Interface 204
- 5-128 C141-E258 204
- 5.4 Command Protocol 205
- (*) Transfers dummy data 207
- 5.4.4 Other commands 211
- 5.5 Ultra DMA Feature Set 213
- 5.5.2 Phases of operation 214
- 5.5.5 Ultra DMA CRC rules 223
- 5.6 Timing 225
- 5.6.4 Power-on and reset 240
- CHAPTER 6 Operations 241
- 6.1.1 Response to power-on 242
- 6.2 Power Save 247
- 6.3 Defect Processing 249
- Sector (physical) 250
- Cylinder 0 250
- (Not used) 250
- 779 780 251
- 6.4 Read-ahead Cache 252
- For MPU work For R/W command 252
- 8,388,608 bytes 252
- 6.4.2 Caching operation 253
- 256
- 6.5 Write Cache 258
- Glossary 261
- Acronyms and Abbreviations 265
- Comment Form 273
Related products and manuals for Internal hard drives Fujitsu MHW2040AC
(133 pages)© 2020, manymanuals.com. All rights reserved. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals