Fujitsu MHW2040AC User Manual Page 218
- Page / 278
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Interface
4) If the host negates HDMARDY- within t
SR
after the device has generated
a DSTROBE edge, then the host shall be prepared to receive zero or one
additional data words. If the host negates HDMARDY- greater than t
SR
after the device has generated a DSTROBE edge, then the host shall be
prepared to receive zero, one or two additional data words. The
additional data words are a result of cable round trip delay and t
RFS
timing
for the device.
5) The host shall assert STOP no sooner than t
RP
after negating
HDMARDY-. The host shall not negate STOP again until after the Ultra
DMA burst is terminated.
6) The device shall negate DMARQ within t
LI
after the host has asserted
STOP. The device shall not assert DMARQ again until after the Ultra
DMA burst is terminated.
7) If DSTROBE is negated, the device shall assert DSTROBE within t
LI
after the host has asserted STOP. No data shall be transferred during this
assertion. The host shall ignore this transition on DSTROBE.
DSTROBE shall remain asserted until the Ultra DMA burst is terminated.
8) The device shall release DD (15:0) no later than t
AZ
after negating
DMARQ.
9) The host shall drive DD (15:0) no sooner than t
ZAH
after the device has
negated DMARQ. For this step, the host may first drive DD (15:0) with
the result of its CRC calculation (see 5.5.5).
10) If the host has not placed the result of its CRC calculation on DD (15:0)
since first driving DD (15:0) during (9), the host shall place the result of
its CRC calculation on DD (15:0) (see 5.5.5).
11) The host shall negate DMACK- no sooner than t
MLI
after the device has
asserted DSTROBE and negated DMARQ and the host has asserted
STOP and negated HDMARDY-, and no sooner than t
DVS
after the host
places the result of its CRC calculation on DD (15:0).
12) The device shall latch the host's CRC data from DD (15:0) on the
negating edge of DMACK-.
13) The device shall compare the CRC data received from the host with the
results of its own CRC calculation. If a miscompare error occurs during
one or more Ultra DMA burst for any one command, at the end of the
command, the device shall report the first error that occurred (see 5.5.5).
14) The device shall release DSTROBE within t
IORDYZ
after the host negates
DMACK-.
15) The host shall neither negate STOP nor assert HDMARDY- until at least
t
ACK
after the host has negated DMACK-.
16) The host shall not assert DIOR-, CS0-, CS1-, DA2, DA1, or DA0 until at
least t
ACK
after negating DMACK.
5-142 C141-E258
- MHW2060AC, MHW2040AC 1
- DISK DRIVES 1
- PRODUCT MANUAL 1
- FOR SAFE OPERATION 2
- Revision History 3
- Preface 5
- Operating Environment 6
- Conventions 6
- Attention 7
- Liability Exception 7
- Important Alert Items 9
- Manual Organization 11
- Contents 13
- Illustrations 19
- CHAPTER 1 Device Overview 23
- 1.1 Features 24
- 1.1.3 Interface 25
- 1.2 Device Specifications 26
- 1.3 Power Requirements 29
- 1.5 Acoustic Noise 33
- 1.6 Shock and Vibration 33
- 1.7 Reliability 34
- 1.8 Error Rate 35
- 1.9 Media Defects 35
- 1.10 Load/Unload Function 35
- 2.1 Device Configuration 40
- 2.2 System Configuration 41
- 2.2.3 2 drives connection 42
- 3.1 Dimensions 44
- 3.2 Mounting 45
- Connector 50
- 3.3.3 Device connection 51
- 3.4 Jumper Settings 52
- 3.4.4 CSEL setting 54
- 4.1 Outline 58
- 4.2 Subassemblies 58
- 4.3 Circuit Configuration 59
- C141-E258 4-5 61
- 4.4 Power-on Sequence 62
- 4.5 Self-calibration 63
- 4.6 Read/write Circuit 65
- 4.6.3 Read circuit 66
- 4.6.4 Digital PLL circuit 67
- 4.7 Servo Control 68
- Theory of Device Operation 72
- 4-16 C141-E258 72
- 4.7.3 Servo frame format 73
- 4.7.5 Spindle motor control 75
- CHAPTER 5 Interface 77
- 5.1 Physical Interface 78
- 5.2 Logical Interface 82
- 5.2.1 I/O registers 83
- 5.3 Host Commands 90
- 5.3.2 Command descriptions 94
- • Default function 110
- • Unload Feature: 110
- • Attribute ID 123
- • Raw attribute value 124
- • Status Flag 124
- • Current attribute value 124
- • Error logging capability 127
- • Check sum 127
- • SMART error logging 128
- • Command data structure 130
- • Error data structure 130
- • Status 130
- • SMART self-test 131
- • Self-test number 131
- • Self-test index 131
- • Test span 132
- • Current LBA under test 132
- • Current span under test 132
- • Feature Flags 133
- (CM) 1 1 1 0 0 1 0 0 149
- • SET MAX ADDRESS 180
- Password information 182
- • SET MAX SET PASSWORD 184
- • SET MAX LOCK 184
- • SET MAX UNLOCK 184
- • Description 186
- 5.3.3 Error posting 203
- Interface 204
- 5-128 C141-E258 204
- 5.4 Command Protocol 205
- (*) Transfers dummy data 207
- 5.4.4 Other commands 211
- 5.5 Ultra DMA Feature Set 213
- 5.5.2 Phases of operation 214
- 5.5.5 Ultra DMA CRC rules 223
- 5.6 Timing 225
- 5.6.4 Power-on and reset 240
- CHAPTER 6 Operations 241
- 6.1.1 Response to power-on 242
- 6.2 Power Save 247
- 6.3 Defect Processing 249
- Sector (physical) 250
- Cylinder 0 250
- (Not used) 250
- 779 780 251
- 6.4 Read-ahead Cache 252
- For MPU work For R/W command 252
- 8,388,608 bytes 252
- 6.4.2 Caching operation 253
- 256
- 6.5 Write Cache 258
- Glossary 261
- Acronyms and Abbreviations 265
- Comment Form 273
Related products and manuals for Internal hard drives Fujitsu MHW2040AC
(133 pages)© 2020, manymanuals.com. All rights reserved. | 0.588 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals